Desktop Metal Launches DuraChain ™ Photopolymers, an all-new Category of 3D Printable Resins that Delivers Two-Part Material Properties and Durability in a Single Pot System

Desktop Metal (NYSE: DM), a global leader in additive manufacturing technologies for mass production, today announced DuraChain ™ — a first-of-its-kind commercial category of photopolymers that uses a material chemistry process known as Photo Polymerization-induced Phase Separation, or Photo PIPS, to deliver breakthrough material properties. 

Highlights 

• DuraChain photopolymers deliver breakthrough elastic and tough material properties for digital light processing (DLP) printing through a Photo Polymerization-Induced Phase Separation (PIPS) process
• Several DuraChain materials – Elastic ToughRubber™ Black and Blanc in various hardnesses – will be exclusively offered on the ETEC Xtreme 8K top-down DLP system
• When illuminated during DLP printing, DuraChain 2-in-1 photopolymers phase separate at the nano level into a material that cures into a resilient, high-performance network
• DuraChain photopolymers will enable a new wave of innovations in 3D printing

The black shroud of the DustBuddie from Dustless Tools is just one rugged end-use application being 3D printed in DuraChain™ materials, which use a 2-in-1 pot chemical reaction to produce stronger new material properties in DLP printing. Desktop Metal says more innovations will be announced in the new resin category this year. (Photo: Business Wire)

Parts produced with standard acrylate-based resins used in DLP 3D printing today are prone to shattering or fracturing upon impact. For decades, the 3D printing industry has been working to incrementally improve these material properties and deliver more durable and elastomeric properties.

DuraChain photopolymers solve this challenge with a breakthrough approach that leverages the Photo PIPs process to produce tough and resilient end-use parts while eliminating the need for a two-part resin. When illuminated during DLP printing, DuraChain materials phase separate into two parts at the nano level and then cure into a resilient, high-performing network that offers a variety of benefits. DuraChain was developed by Texas-based Adaptive3D, which was acquired by Desktop Metal in 2021.

Unlike two-part resins, DuraChain photopolymers demonstrate a long pot life of roughly one year, depending on environmental conditions, making them more suitable for volume production and reducing waste from spoiled, unused material.

“DuraChain photopolymers signal a new era in DLP printing that delivers material properties that compete with thermosets in a long pot-life material,” said Ric Fulop, Co-Founder and CEO of Desktop Metal. “Parts printed with DuraChain resins are high performing in a wide range of temperatures and offer other important benefits that will quickly lead to new material innovations in DLP printing.”

The Challenge of Commercializing Photo PIPS

Photopolymers that cure using the Photo PIPs process have been studied by researchers for years but have not been broadly commercialized – primarily because DLP 3D printing hardware has struggled to print the high viscosity resins required to make use of this process.

Most DLP systems feature a bottom-up printing process in which a projector is placed below the build area and illuminates each part layer through a transparent tray, while the part advances upward suspended to a build tray. Because Photo PIPS resins require more energy to cure and are relatively heavy compared to standard resins, they are challenging to suspend from a build plate during bottom-up DLP printing.

Desktop Metal’s DuraChain materials will be printable on one of the additive manufacturing industry’s only top-down DLP systems, the ETEC Xtreme 8K.

A New Line of DuraChain Photopolymers

Several DuraChain materials will be exclusively available on the ETEC Xtreme 8K: Elastic ToughRubber (ETR) 70 and 90, both of which are offered today and which differ in Shore A durometer value. ETR 70 is available in Black while ETR 90 is available in both Black and Blanc, which produces white parts that can be dyed to any color for production.

ETR is already being used to 3D print end-use parts. A case study showcases how Dustless Tools, a maker of construction and industrial vacuum systems based in Utah, uses the rugged ETR material to domestically produce its DustBuddie for demolition hammers. The rugged application requires the material to have high energy return, tear strength, resilience and other durability properties.

Additionally, a new video also showcases the use of ETR 70 Black by Aerosport Additive, a premium service bureau for 3D printed prototypes and production parts outside of Columbus, Ohio. Aerosport has purchased several ETEC Xtreme 8K printers and serves the aviation, automotive, medical, electronic, and military industries, among others.

Parts 3D printed in a variety of DuraChain materials will be on display May 17-19 in Detroit at RAPID + TCT, North America’s largest and most-influential additive manufacturing event. Desktop Metal’s production-capable printing platforms for metals, polymer, elastomers, ceramics, composites, and upcycled wood materials will be showcased in Booth No. 3301 at the main entrance of the show.

Original Source